- Heidolph Mr Hei-standard
- Heidolph Mr Hei Standard
- Heidolph Mr Hei-standard Service Manual
- Heidolph Mr Hei Standard Manual
Heidolph® MR Hei-End Magnetic Hot Plate Stirrer, Brinkmann® Heidolph® MR Hei-End Magnetic Hot Plate Stirrer, Brinkmann®. We may terminate your access, or suspend any user's access to all or part of the Site, without notice, for any conduct that we, in our sole discretion, believe is in violation of any applicable law or is harmful to. MR Hei-Standard, MR Hei-Tec. The instructions stipulated in this instruction manual are followed. Errors must be eradicated immediately; especially those which jeopardize safety. Heidolph Instruments does not accept liability for personal injury or damage to property which may result. Mesostructured colloidal materials find widespread application in science and technology, as model systems for fundamental studies on atomic and molecular materials 1,2, as photonic materials 3,4, as drug delivery systems 5,6, as coatings 7 and in lithography for surface patterning 8,9.Since lyophobic colloids are metastable materials that eventually aggregate irreversibly due to the. Please read this Instruction Manual thoroughly before operating your unit. The following symbols are intended to assist the user in the safe and efficient operation of Heat-On. Important WARNINGS. 505-81500-00 1 x MR Hei-Standard 2 x Heat-On 25ml Insert 2 x Heat-On 50ml Insert 2 x Heat-On 100ml Insert.
Advertising
24
Error
code
Mode
Cause
Consequence
Measure
„E21“ *
a. Temperature sensor
dropped from the medi-
um.
um.
Position the tempera-
ture sensor at the
measuring point.
measuring point.
Perform a reset.
b. Cool medium is refilled
when heating function is
switched on and tempera-
ture sensor is connected.
switched on and tempera-
ture sensor is connected.
(IMPORTANT: Only refill the
cool medium when the heat-
ing function is switched off).
cool medium when the heat-
ing function is switched off).
Perform a reset.
„E22“ *
a. Temperature sensor lo-
cated outside of the me-
dium when switching on
the heating.
dium when switching on
the heating.
Position the tempera-
ture sensor at the
measuring point.
measuring point.
Perform a reset.
b. The temperature on the
sensor of the temperature
sensor is too low during
the first 10 minutes.
sensor is too low during
the first 10 minutes.
c. For physical reasons, a
temperature increase is
not possible.
not possible.
Reduce the medium
quality or optimize heat
conduction.
conduction.
„E23“
(o
n
ly
i
n
Pr
eci
se
-M
o
d
e)
The actual temperature ex-
ceeds the set temperature on
the sensor of the temperature
sensor by more than 25°C:
ceeds the set temperature on
the sensor of the temperature
sensor by more than 25°C:
a. Temperature control de-
Epson printer xp 820 drivers. fective.
b. Exothermic reaction.
c. Test setup not optimal.
c. Test setup not optimal.
Check test setup.
Please contact our
Please contact our
Technical Service.
„E33“
Heating button defective.
Please contact our
Technical Service.
„E34“
Stirring button defective.
„E35“
Hei-Guide rotary-push button
defective.
defective.
„E41“
Motor defective.
Heating function off.
Stirring function off.
Stirring function off.
„E51“,
„E52“,
„E53“
„E52“,
„E53“
a. Sensor break.
b. Temperature sensor is
b. Temperature sensor is
connected or disconnected
whilst the heating function
is switched on.
whilst the heating function
is switched on.
(IMPORTANT: The tempera-
ture sensor must only be
connected or removed when
the heating function is
switched off)
ture sensor must only be
connected or removed when
the heating function is
switched off)
Heating function off. Replace temperature
sensor (only in case of
'a'.).
'a'.).
Switch off the device.
Connect temperature
sensor (see chapter
'Installation
'Installation
Switch on the device.
* The monitoring of this safety function can be disabled by switching off the Safety Plus function (see chapter
'Operation' - 'Heating' - 'Safety Plus (MR Hei-Tec)'.
Advertising
This manual is related to the following products:
Popular Brands
Popular manuals
Advertising
23
Error codes
NOTICE
Error code displayed on the device
1. Perform a reset.
2. Implement the measures suggested in the table below.
2. Implement the measures suggested in the table below.
MR Hei-Standard
Error code
Cause
Consequence
Measure
LED I/O flashes
one time
one time
-
Heating function off. Please contact our
Technical Service.
LED I/O flashes
two times
two times
The actual temperature
exceeds the set
temperature on the sensor of
the temperature sensor by
more than 25 °C:
exceeds the set
temperature on the sensor of
the temperature sensor by
more than 25 °C:
a. Temperature control
defective.
b. Exothermic reaction.
c. Test setup not optimal.
c. Test setup not optimal.
Check test setup.
Please contact our
Please contact our
Technical Service.
LED I/O flashes
three times
three times
a. Speed control knob
defective.
b. Temperature control knob
defective.
c. Heating button defective.
Heating function off. Please contact our
Technical Service.
LED I/O flashes
four times
four times
Motor defective.
Heating function off.
Stirring function off.
Stirring function off.
LED I/O flashes
five times
five times
Heidolph Mr Hei-standard
a. Sensor break.
b. Temperature sensor is
b. Temperature sensor is
connected or disconnected
whilst the heating function
is switched on.
whilst the heating function
is switched on.
(IMPORTANT: The tempera-
ture sensor must only be
connected or removed when
the heating function is
switched off)
ture sensor must only be
connected or removed when
the heating function is
switched off)
Heating function off. Replace temperature
sensor (only in case of
“a”.).
“a”.).
Switch off the device.
Connect temperature
sensor (see chapter
'Installation
'Installation
Switch on the device.
MR Hei-Tec
Error
code
Heidolph Mr Hei Standard
Mode
Cause
Consequence
Measure
„E11“,
„E12“,
„E13“,
„E14“
„E12“,
„E13“,
„E14“
-
Heidolph Mr Hei-standard Service Manual
Heating function off. Please contact our
Hamilton beach blender 54615 user manual. Technical Service.
Advertising
This manual is related to the following products:
Heidolph Mr Hei Standard Manual
Popular Brands
Popular manuals